<rp id="ehf8e"></rp>
<th id="ehf8e"></th>

  1. <tbody id="ehf8e"><noscript id="ehf8e"></noscript></tbody>

    <tbody id="ehf8e"><noscript id="ehf8e"></noscript></tbody>

    春林門窗

    聯系我們
    濟南槐蔭春林門窗廠
    地址:濟南栗山路美里湖消防站對面
    電話:13506414902
    手機:13506414902
    聯系人:張經理
    當前位置:首頁-新聞資訊 -公司動態
    公司動態
    斷橋鋁門窗如何更換密封條?
    來源: 2016-01-25 13:48:58
    斷橋鋁門窗如何換密封條?
    Broken bridge aluminum doors and Windows to replace the sealing strip?
    1)密封材料規格較多,可向廠家詢問具體規格。
    1) sealing material specifications, can ask manufacturer specifications.
    2)換準備:檢查安裝密封條的部位有無破損、變形;密封條的種類、規格、截面形狀是否符合要求,有無缺陷或損傷。密封條應在清潔、干燥、溫暖的環境下施工。濟南斷橋鋁門窗
    2) replacement preparation: check whether there is any breakage, deformation on installation of sealing part; Sealing strip type, specification, cross section shape is in accordance with the requirements, the presence of defects or damage. Sealing strip should be clean, dry, warm environment construction.
    密封條安裝前應進行松弛處理,使其消除卷曲包裝時的形變,恢復彈性。方法是打開包裝,將密封條平放或懸掛在支架上,在20℃左右的環境中處理24小時。冬季施工時,可用溫水浸泡的方法處理密封條,但不允許直接用明火加熱。
    Sealing strip should be done before installation relaxation process, eliminating curling when packing deformation, elastic recovery. Method is open the packing, sealing strip flat or hanging on the scaffold, in about 20 ℃ environment treatment for 24 hours. When winter construction, can use warm water immersion method processing sealing strip, but are not allowed to directly use the firing.
    清理窗框和密封凹槽,使其保持清潔、干燥。
    Clean up the window frames and seal grooves, keep it clean and dry.
    3)采用手工和滾壓工具將密封條安裝部位完全嵌入到異型材特設的嵌槽內。密封條裝到窗的轉角處時不要剪斷,剪成45°角邊緣要留一點相連,防止收縮時拉斷出現開口。框扇之間密封條嵌裝時要留出1%的余量,以防收縮斷口。
    3) the use of manual and rolling tools install the sealing parts completely embedded in different profile AD hoc embedded groove. Sealing strip into the corner of the window, don't cut, cut into 45 ° Angle edge to leave a bit to prevent shrinkage when pulled from opening. Box door sealing strip between embedded to set aside 1% of allowance, to prevent shrinkage fracture.
    手工嵌裝密封條時應特別注意:密封條不允許拉延。剪斷時應留有收縮余量。若有斷頭,不要設在拐角處,好在縱向位置,且將端口處對緊,并用粘合劑粘貼牢固。
    Should pay special attention to: when manually flush seal sealing strip drawing is not permitted. Cut, shrinkage allowance shall be maintained. If you have beheaded, do not in the corner, the best in the vertical position, and the port to tight, and cement paste is firm.
    4)框體的密封條,從左下角開始,順時針旋轉,沿膠條的槽口移動回到原位,注意要嵌入槽內并保存一定的伸縮余量。
    4) the box body sealing strip, starting from the lower left corner, clockwise, along the strip rabbet moving back to the in situ, pay attention to embed groove and save some telescopic allowance.
    5)如果要換扇上的密封條,則起點需從扇上框的中間開始。
    5) if you want to replace the sealing strip on the fan, the starting point to the middle of the box from the fan.
    [聲明] 本站圖片均由網站所有方提供,部分圖片來源于網絡,如有任何疑問請第一時間與我們聯系,未經溝通本站不承擔相關法律責任!
    在線咨詢
    陕西快乐10分